GW Instek
Sub Categories
Features: Single Output Dual Range Max. 200WHigh resolution: 1mV/1mA0.01% load/line regulation, 350uVrms rippleAuto step runing with timer setting and 100 Sets memorySafety design: OVP,OCP & OTP;Output ON/OFF controlSelf-test and software calibrationHighly visible vacuum-fluorescent displayFront and rear output terminalStandard interface : RS-232C, GPIBOption : European Jack Type Terminal
Features: 2/3/4 Independent Isolated Output4 LED Display Sets: 3 digits after decimal point Minimum Resolution : 1mV/1mA(GPD-2303D/GPD-3303S/GPD-4303S)100mV/10mA(GPD-3303D)Digital panel control(rotary encoder Switch, rubber key with indicator) User-friendly operation, coarse/fine volume control 4 Sets Save/Recall Key-Lock Output on/off Tracking Series and Parallel mode Smart cooling fan achieving low noise USB Standard InterfacePC Software & USB Driver Labview driver
Features : -Operating voltage (DC):1.5V~150V-Operating Mode : C.C / C.V / C.R / C.P / CC+CV / CR+CV / CP+CV -Parallel Connection of Inputs for Higher Capacity (Max : 9,450W)-Support of High Slew Rate:Max 16A/us-Run Program Function(GO/NO GO Test)-Sequence Function for High Efficient Load Simulations-Commands are compatible with Kikusui PLZ-4W model.-Dynamic(Switching) Function:0.0166Hz ~20kHz-Soft Start Function:Off / On(1~200ms, Res:1ms)-Adjustable OCP / OVP / OPP / UVP Setting -Short Circuit Function-Timer function : Elapsed Time of load on -Cut Off Time(Auto Load Off Timer ):1s to 999h 59min 59s or Off -External Channel Control / Monitoring via Analog Control Connector-Setup Memories:100 sets-3.5 Inch TFT LCD Display-Multi Interface : USB 2.0 Device / Host , RS-232 , GPIB (Optional)
Features: -Sequence function to do high Efficient load simulations-Flexible configuration with mainframes and plug-in modules-Multiple independent load inputs up to 8 channels in a mainframe-Parallel connection of inputs for increased load capacity-Parallel connection of inputs for static and dynamic tests-Multiple channels run for dynamic tests under one clock control -Maximum rated power for low range high resolution CC tests-Von setting and Von on/off for start-up Von tests-Program mode to create work routines for repetitive tests-OPP/OCP/OVP/OTP protections-External channel control/monitoring via an analog control connector-Multi-Interface USB Device / Host, RS-232C, and GPIB (Optional) -Multi-mainframe link up to 5 mainframes in a system
Features - 6 1/2 Digit measurement resolution- Dual measurement for Voltage and Current- AC&DC Current measurement range:30mA/300mA/3A/30A/300A(Max)AC Voltage measurement range:200mV/2V/20V/200V/600V(Max)DC Voltage measurement range:200mV/2V/20V/200V/1000V(Max)- Auto zero circuit- Standard Interfaces: USB, GPIB
Features: ※ 30000 Counts Display ※ High Accuracy 0.05% ※ Hi/Lo Comparator and Limit Percent Setting ※ Measurement of REL, Actual and % Value ※ Continuous or Triggered Measurement Mode ※ Temperature Compensation and Measurement ※ Four-Terminal Measurement Technique ※ Auto-Recall Last Setting After Power OFF and ON Again ※ Alarm Setting for PASS/FAIL ※ Scan, Handler Interface(Standard) ※ Manual or Autoranging ※ RS-232C+GPIB (Option)
Features: ※ 3 1/2 Digits 0.5" LED Display※ Measures from 20mΩ ~ 20kΩ in 7 Ranges ※ 1A High Test Current ※ High Resolution 10uΩ ※ Hi/Lo Comparator Indicator and Buzz Alarma
Features: ※ Loop Test ※ Auto-Search ※ Seif-Diagnosis ※ Over-Load Protection ※ Measures 1800 Kinds of Device ※ 54/74 Series TTL ※ 4000 and 4500 Series CMOS ※ Test Socket: 28 Pin